Find Downloads, Manuals, Tutorials, FAQ (Frequently Asked Questions), Tips & Tricks, How to’s, Firmware, Drivers, Software, Problem Solving about RM-VL 2) On the Sony RM-VL remote press and hold the black SET button in the upper left corner. While holding the SET button down, press and release the small. User manual, users manuals, user guide, operating instructions. SONY – Remote Controls. Operating Instructions, Download RM-VL pdf user manual.
|Published (Last):||2 April 2007|
|PDF File Size:||3.35 Mb|
|ePub File Size:||7.46 Mb|
|Price:||Free* [*Free Regsitration Required]|
If the [Set] LED pauses and then flashes twice the button already contains a learned signal and must be reset see instructions below. If your device brand is not listed, try the codes listed for other brands. Search for a preset code: When the last LED turns off the remote has been reset. Contact support Contact your Sony Support team. Press the ENT button. Table Of Contents When to replace the batteries Press the corresponding Component Select button for the component you have set up.
Press the appropriate component select button sony rm vl600 manual the component being set sony rm vl600 manual. If the [Set] LED flashes twice the button already contains a macro and must be dony see instructions below.
Page 38 For the customers in the U. Service Centres List of Sony offices in Asia Pacific region that provide after-sales service activities. Remove the batteries, press each button twice, and then put the batteries back in. Start over from the beginning.
Sony RM RM-VL600 Operating Instructions Manual
This manual also for: If more than one code number is listed for the manufacturer, repeat the procedure, entering one code at a time until you find one that works. To get the full experience on Sony. Some functions of a device may not be controllable by the remote. As the command is cleared the [Set] LED will turn off. These limits are designed to provide reasonable protection against harmful interference in a residential installation. Follow the sony rm vl600 manual above but press and hold the component or system button for three seconds or until the [Set] LET starts to sony rm vl600 manual faster.
When finished, press [Set] to save.
SONY RM-VL user manual – Operating Instructions
You should be able to learn a 3 sony rm vl600 manual 4 step macro in mxnual manner onto any button. If you are manuap the Commander with a factory-set Sony components, skip the following procedures. Features Centralized control of Sony AV components with this one remote commander This Commander is preset at the factory to operate Sony brand components, so you can use it out of the box as a control center for your Sony AV components.
Was this information helpful?
Page 23 Page 24 – Notes on programming the signals for an The top four device LEDs will each illuminate one by one. If more than one code number is listed for your device brand, enter one code at a time sony rm vl600 manual you find one that works.
Programming Codes Select the brand name from the drop down list for each device for which you want tm see codes. When to replace the batteries If you change the component code page sont after setting the Power-On function, the Power-On function is cleared. All Component Select buttons light up when you press these buttons, and then turn off when you release them. Executing a Series of Commands — System Control Functions With sony rm vl600 manual System Control function, you can program a series of operating commands, and execute them by pressing just one button.
The sony rm vl600 manual page was printed from RemoteCentral.
Press the Mabual Select button for the desired component. In this case, program the remote control signals with the Learning function page As commands are cleared all component LEDs will turn off.
Sony Universal Remote RM-VL User Guide |
The SET indicator will illuminate. Program a micro macro anywhere! Where can I buy Sony products? Visit our Community and share your experiences and solutions sony rm vl600 manual other Sony customers. Page of 52 Go. How to test if a remote control is sending an Infrared IR signal.
By pressing ‘print’ button you will print only current page. Page 2 For the customers in the U. Startup Guide This guide shows you how to set the Remote Commander to operate your components.