74LS688 DATASHEET PDF

Texas Instruments 74LS Logic Comparators are available at Mouser Electronics. Mouser offers inventory, pricing, & datasheets for Texas Instruments . December INTEGRATED CIRCUITS. 74HC/HCT 8-bit magnitude comparator. For a complete data sheet, please also download. Part Number: 74LS, Maunfacturer: National Semiconductor, Part Family: 74, File type: PDF, Document: Datasheet – semiconductor.

Author: Vudonos Makus
Country: Indonesia
Language: English (Spanish)
Genre: Travel
Published (Last): 17 August 2007
Pages: 76
PDF File Size: 6.66 Mb
ePub File Size: 11.49 Mb
ISBN: 485-9-44028-812-3
Downloads: 24578
Price: Free* [*Free Regsitration Required]
Uploader: Zutaur

Glitchy output shouldn’t be a problem — it needs to be inverted for the D-type flip flop’s clock anyway, so I’m using a 74LS14 inverter, which has Schmitt inputs and should clean up the signal into a nice, sharp positive-going square wave.

This would also add about 62 nS to your latch clock which right now is only 3 gate delays long and would be difficult to see on an old low bandwidth scope. When the system comes up from a reset, a 74LS with its inputs all tied to ground is connected to the data lines of the CPU and the data bus tranceivers are switched off — this feeds the CPU NOPs until the address equals what’s set on the DIP switch.

I’m not talking about little tiny noise spikes. It might work, but I don’t like it much.

Most Related  AYUDAR A MORIR IONA HEATH PDF

Comparator 74LS688 DIP20

I’m not that good with circuit design, but is it possible a monostable multivibrator one-shot would do the job? If you expect to use it, you ddatasheet to turn the enable off during the time when the compare inputs are in transition. It’s comparing the high four address bits to a 4-position DIP switch.

For example, going from 9 to A might give a false compare of B for a few nanoseconds. I’ve never had to use one. It’s an 8-bit comparator, but it’s cheaper than the 74LS85 and has an enable input.

A way to datasheeh that would be to de-glitch the circuit by adding a synchronizing flip-flop running at 16MHz just before the latching flip-flop. It is a glitchy signal. I got lost reading that. It may even make it worse. Glitchy output shouldn’t be a problem — glitch, I see how you got your nickname.

74LS IC 8-BIT IDENTITY COMPARATOR — Majju

Any decoder, like the will create big nasty full swing glitches that can only be removed with the proper clocked gating or latching. In dafasheet words, what function does it serve?

This might cause a false trigger if your address trap was at B. Hi No it won’t. My calculations say yes, with lots of time to spare, but I’d like others’ opinions. I’m currently designing the power-on-jump circuit for my processor board. As the address lines transition and settle out, they might very well set up a glitch that agrees with the test condition, well before you datashest.

Most Related  ORAL AND MAXILLOFACIAL INFECTIONS TOPAZIAN PDF

I don’t do well with word descriptions of circuits–can you draw a schematic? There may be better ways to do this job so keep tinkering. You’re depending too much on the propagation delay of the 74 and the creating a clock pulse of the minimum required width t wclk on your datasheet.

Here’s the pieces relevant to Power on Jump: You could then use it as a clock.

74LS688 Datasheet PDF – ETC

Note that this would take away 62 nS from the access time of the first instruction 74ld688 after the proper address compare, but it should be OK if you are using newer memory devices.

Hi I doubt you’ll be able to run the output of the directly to a clock. This sets the D-type flip flop, which switches off the NOP generator and turns on the bus tranceivers.

This is all fine. You can’t use it while the inputs are changing. Just to scratch my own curious itch, what does the connect to?